Entries into grassland class of this yr’s Innovations Competitors centre on methods to enhance the effectivity of resowing, rolling and ridding fields of weeds. Scroll right down to see a few of the most inventive concepts.
See additionally: 9 steps to getting a spring reseed proper
Andrew Carbis’ curler seeder
A modification to his set of 6.3m He-Va Cambridge rolls means Cornish dairy and beef farmer Andrew Carbis can now sow grass and roll in a single move.
The roller-seeder additionally opens up the choice of min-tilling stubbles with out dragging trash throughout the sphere – an issue he was discovering along with his Accord DL seeders – and means he can evenly distribute grass with out leaving rows and bout marks.
Mr Carbis says his model of the idea was put collectively for £2,720, together with the price of the air seeder – considerably cheaper than the £9,000 that Opico needed for the equipment.
Central to the design is a nine-outlet Bullock Tillage air seeder mounted on a cantilever metal that runs from the drawbar and juts out over the rear wheels. This format permits the curler to fold up horizontally in the direction of the tractor and retains the hopper stage. It additionally means he can see the seed stage from the cab and fill the hopper by climbing on the curler rings.
Seed pipes feed spreader plates mounted in entrance of a row of Accord following tines, that are introduced into work concurrently the hydraulically managed He-Va Shattaboards.
Output is adjustable from the cab and typical journey pace is 6kph. In unfastened floor, Mr Carbis says he rolls as soon as earlier than making one other move with the seeder on. He then normally rolls once more to go away a very tight seed-bed.
Sam Woodhouse’s weed wiper
Land agent Sam Woodhouse made probably the most of his furlough time by constructing a weed wiper to assist eliminate Cumbrian rush infestations in grassland.
The 3m-wide implement is towed behind a Honda ATV and was assembled utilizing pretty low-cost supplies, together with scrap metallic to kind the primary A-frame and a sprig tank he already had.
That is strapped to the ATV’s rear body and it primes the horizontal part of sealed wastewater pipe till the overlapping 250mm lengths of nylon ropes are damp. These got here as a part of a Greenleaf wick string equipment.
It runs 250mm off the bottom and makes use of little or no herbicide, Mr Woodhouse says. The following job is so as to add peak adjustment. Whole value was £150.
Rob Chatwin’s ballast curler tow equipment
In the course of the first lockdown of 2020, Rob Chatwin and his contractor good friend, Matt, designed and constructed a rear tow equipment for a 2.4m ballast roll.
This has a sturdy box-section body working excessive of the curler, with a lorry axle sitting on the rear on pivoting arms.
A pair of hydraulic rams run from the highest of the body to the axle, permitting the curler to be raised or lowered as required.
The duo made use of elements and metal they already had and solely outsourced the rams, which have been custom-made by an area hydraulic firm.
Malachy Dolan’s weed licker
Malachy Dolan constructed a three-point linkage-mounted weed licker to focus on cussed gorse.
It was primarily constructed utilizing scrap discovered on the farm, together with absorbent bristles from an previous wheel brush beforehand used for cleansing vehicles. A 12V pump feeds the nozzles from the 200-litre tank above and the reel is pushed hydraulically.
At 2.4m broad, it may be utilized in tough discipline corners and peak is adjusted utilizing the tractor’s hyperlink arms.
Mr Dolan says the benefit of utilizing bristles moderately than rope is that they scale back the probability of drips and improve the floor space for higher contact with the weeds. All in, he reckons it value about £400 to construct.
Matthew Kirk’s silage wrap provider
Maintaining his Kuhn wrapper equipped with rolls of plastic was a unending process for 22-year-old Matthew Kirk.
So, as an alternative of utilizing a quad bike and trailer that solely had room for 4 at a time, he manufactured a wrap provider that could possibly be lifted with the bale squeeze moderately than pallet tines.
The bottom of the body was shaped from a recycled diesel tank, which was heavier than essential however helped to maintain the fee down. Beneath that, he connected two metal tubes for the squeeze arms to slip by means of. In work, the telehandler headstock is crowded again and the tines widened to carry the body tight.
It might probably transport 20 rolls and has been designed so there is no such thing as a probability of them falling out. He says it has made maintaining with the baler a lot simpler, notably as it may be carted round with the JCB telehandler and doesn’t require every other attachments.
Lindsay Gracey’s ATV-mounted spot sprayer
A mini spot sprayer has allowed Lindsay Gracey of Rathfriland, Nation Down, to rid grassland of distinguished weeds with out counting on a hand lance.
It matches to the entrance of any quad bike through an angle iron body and is paired with an everyday ATV sprayer mounted on the again. A size of hose takes the chemical to a financial institution of 5 triggers that have interaction the 10 spray nozzles in pairs.
Whole value was £300, with a lot of the bits sourced from eBay.
David Powell’s ATV lock-up
After having two ATVs pinched, David Powell determined to stiffen up his defences with a lock-up field.
It began life as a big diesel tank, which he has closely strengthened. To breach the container, thieves first need to get by means of a shrouded heavy-duty padlock and a number of other different awkward security options.
The tank rolls on castor wheels and opens on hinges, making it straightforward for the rider to drive in and dismount.
To realize your objectives, you want the fitting instruments for the job. If what you want doesn’t exist, merely invent it. We share this ethos and used it to create the Ineos Grenadier. An uncompromising 4×4, constructed on objective and there to assist those that want it most.